Tool Usage Guide
Updated By Chris Pagan

Only the mechanically inclined will understand….

 

HAMMER: Originally employed as a weapon of war, the hammer is now used as a kind of divining rod to locate expensive parts not far from the object we are trying to hit.

 

MECHANIC'S KNIFE: Used to open and slice through the contents of cartons delivered to your front door; works particularly well on boxes containing leather goods.

 

ELECTRIC HAND DRILL: Normally used for spinning steel Pop rivets in their holes until you die of old age.

 

PLIERS: Used to round off bolt heads.

 

HACKSAW: One of a family of cutting tools built on the Ouija board principle. It transforms human energy into a crooked, unpredictable motion, and the more you attempt to influence its course, the more dismal your future becomes.

VISE-GRIPS: Used to round off bolt heads and transfer intense welding heat to the palm of your hand.

 

OXYACETYLENE TORCH: Used almost entirely for lighting various flammable objects in the garage on fire.

 

WHITWORTH SOCKETS: Once used for working on older British cars and motorcycles, they are now used mainly for impersonating that 9/16 or 1/2 socket you've been searching for the last 15 minutes.

 

DRILL PRESS: A tall upright machine useful for suddenly snatching flat metal bar stock out of your hands smacking you in the chest and flinging your beer across the room, splattering it against that freshly painted part you were drying.

 

WIRE WHEEL: Cleans rust off old bolts and then throws them somewhere under the workbench with the speed of light. Also removes fingerprint whorls and hard-earned guitar calluses in about the time it takes you to say, "Ouc...."

 

HYDRAULIC FLOOR JACK: Used for lowering a car to the ground after you have installed your new front disk brake setup, trapping the jack handle firmly under the fender.

 

EIGHT-FOOT LONG DOUGLAS FIR 2X4: Used for levering a car upward off a hydraulic jack.

 

TWEEZERS: A tool for removing wood splinters.

 

PHONE: Tool for calling your neighbor to see if he has another hydraulic floor jack.

 

SNAP-ON GASKET SCRAPER: Theoretically useful as a sandwich tool for spreading mayonnaise; used mainly for getting dog-doo off your boot.

 

E-Z OUT BOLT AND STUD EXTRACTOR: A tool that snaps off in bolt holes and is ten times harder than any known drill bit.

 

TIMING LIGHT: A stroboscopic instrument for illuminating grease buildup.

 

TWO-TON HYDRAULIC ENGINE HOIST: A handy tool for testing the tensile strength of ground straps and brake lines you may have forgotten to disconnect.

 

CRAFTSMAN 1/2 x 16-INCH SCREWDRIVER: A large motor mount prying tool that inexplicably has an accurately machined screwdriver tip on the end without the handle.

 

BATTERY ELECTROLYTE TESTER: A handy tool for transferring sulfuric acid from a car battery to the inside of your toolbox after determining that your battery is dead as a doornail, just as you thought.

 

AVIATION METAL SNIPS: See hacksaw. Note: Alternative to your wife good sewing scissors.

 

PHILLIPS SCREWDRIVER: Normally used to stab the lids of old-style paper-and-tin oil cans and splash oil on your shirt; can also be used, as the name implies, to round out Phillips screw heads.

 

AIR COMPRESSOR: A machine that takes energy produced in a coal-burning power plant 200 miles away and transforms it into compressed air that travels by hose to a Chicago Pneumatic impact wrench that grips rusty bolts last tightened 60 years ago by someone in Springfield, and rounds them off.

 

PRY BAR: A tool used to crumple the metal surrounding that clip or bracket you needed to remove in order to replace a 50 cent part.

 

HOSE CUTTER: A tool used to cut hoses 1/2 inch too short.